Abandonment Equipment Packages
Isolate, clean out and permanently seal a well from one supplier and one call. Drillable 10,000 psi plugs through 8-5/8″, set and cemented in one trip.
Four groups, one call
Zonal Isolation & Sealing Tools
Permanently seal off formations and stop fluid or gas migrating up the wellbore.
- Permanent bridge plugs: high-pressure plugs set to isolate old production or injection zones.
- Permanent packers: mechanically isolate targeted sections of the casing string.
- Wireline & mechanical cement retainers: lock into the casing so crews can squeeze cement into perforations or behind casing, then leave a cement plug on top.
Wellbore Prep, Cleanout & Milling
Before a permanent plug goes in, the casing has to be clean of debris, scale and old downhole equipment.
- Casing scrapers: clean the casing wall so plugs and retainers seal properly.
- Mills & bits: grind out old packers, stuck liners or debris before the final plug.
- Power swivels: 85-ton surface units to rotate the work string for milling and cleanouts.
Cased-Hole Fishing
Older wells often have junk or failed tubing left downhole.
- Fishing tools: spears, overshots and catch tools to retrieve stuck items or parted tubing.
- Jack trucks: 125-ton hydraulic units to pull stuck tubing hangers or remove old casing slips at surface.
Pressure Control & Surface Handling
- Valves & flanges: high-pressure valves, spools and BOP components to keep well control during service-rig work.
- Pack-off / RS heads: seal around slickline or wireline during the setting phase.
Plugs, Retainers & Setting Tools
Drillable, 10,000 psi plugs through 8⅝″; set and cement in one trip; surface cement jobs without a service rig.
| Tool | Use | Size range | Pressure rating |
|---|---|---|---|
| DB-10 Drillable Bridge Plug | Permanent, drillable | 60.3 – 219.1 mm (2⅜″ – 8⅝″) | 68.9 MPa (10,000 psi) at 150 °C (300 °F) |
| DB-5 Drillable Bridge Plug | Permanent, drillable | 114.3 – 177.8 mm (4½″ – 7″) | 34.5 MPa (5,000 psi) at 120 °C (250 °F) |
| Kappa WHM Bridge Plug | Permanent, drillable | 114.3 – 508.0 mm (4½″ – 20″) | 68.9 MPa (10,000 psi) to 8⅝″; 200 °C (400 °F) and 425 °C (800 °F) versions |
| Kappa WHM Cement Retainer | Wireline or mechanical set | 114.3 – 339.7 mm (4½″ – 13⅜″) | 68.9 MPa (10,000 psi) through 8⅝″; to 227 °C (440 °F) |
| Kappa Surface Cementer | Surface cementing without a service rig | Standard casing sizes | — |
| B110 & 120 Hydraulic Setting Tool | Hydraulic set, on tubing, coil or drill pipe | 46.0 – 107.9 mm tool OD (1.81″ – 4.25″) | — |
| MST Mechanical Setting Tool | Mechanical set, one-trip squeeze work | 114.3 – 273.1 mm casing (4½″ – 10¾″) | — |
Also in stock: HMII setting kits (114.3, 139.7 and 177.8 mm / 4½″, 5½″, 7″), CR snap latch assemblies, tubing or braided-line cement dump bailers and Class G cement.
Plugs, retainers and packers in the Tools Catalogue
Sizes and pressure ratings for the plugs, retainers and packers above are in the Tools Catalogue.
Planning an abandonment program?
Tell us the well. Dispatch 24/7.
Fort St. John (250) 785-6100Grande Prairie (780) 228-6616